Mobile |
| Mobile module |
4G (LTE) – Cat 6 up to 300 Mbps, 3G – Up to 42 Mbps |
| Status |
Signal strength, SINR, RSRP, RSRQ, Bytes sent/received, connected band, carrier aggregation, IMSI, ICCID |
| SMS |
SMS status, SMS configuration, send/read SMS via HTTP POST/GET, Email to SMS, SMS to Email, SMS to HTTP, SMS to SMS, SMS auto reply |
| USSD |
Supports sending and reading Unstructured Supplementary Service Data messages |
| Black/Whiles list (planned) |
Operator black/white list |
| Multiple PDN |
Possibility to use different PDNs for multiple network access and services |
| Band management |
Band lock, Used band status display |
| APN |
Auto APN |
| Bridge mode |
Direct connection (bridge) between mobile ISP and device on LAN |
Wireless |
| Wireless mode |
802.11 b/g/n, 2×2 MIMO, Access Point (AP), Station (STA) |
| WiFi security |
WPA3-EAP, WPA3-SAE, WPA2-Enterprise-PEAP, WPA2-PSK, WEP; AES-CCMP, TKIP, Auto Cipher modes, client separation |
| ESSID |
ESSID stealth mode |
| Wireless Hotspot |
Captive portal (Hotspot), internal/external Radius server, SMS OTP, MAC auth, built in customizable landing page, walled garden |
Ethernet |
| WAN |
1 x WAN port (can be configured as LAN) 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover |
| LAN |
1 x LAN ports, 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover |
Network |
| Routing |
Static routes, Dynamic routes (planned) |
| Network protocols |
TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP (planned), SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet client, SNMP (planned), MQTT (planned), Wake on LAN (WOL) (planned) |
| VoIP passthrough support |
H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets |
| Connection monitoring |
Ping Reboot, Wget reboot, Periodic Reboot, LCP and ICMP for link inspection |
| Firewall |
Port forwards, traffic rules, NAT rules, custom rules |
| DHCP |
Static and dynamic IP allocation, DHCP Relay, Relayd |
| QoS / Smart Queue Management (SQM) (planned) |
Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e |
| DDNS (planned) |
Supported >25 service providers, others can be configured manually |
| Network backup |
Mobile, Wired and WiFi WAN options, each of which can be used as an automatic Failover |
| Load balancing |
Balance Internet traffic over multiple WAN connections |
| SSHFS (optional) |
Possibility to mount remote file system via SSH protocol (not available in standard FW) |
Security |
| Authetication |
Pre-shared key, digital certificates, X.509 certificates |
| Firewall |
Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T |
| Attack prevention |
DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks) |
| VLAN |
Tag based VLAN separation |
| Mobile quota control |
Custom data limits for both SIM cards |
| WEB filter (planned) |
Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only |
| Access control |
Flexible access control of TCP, UDP, ICMP packets, MAC address filter |
VPN |
| OpenVPN |
Multiple clients and a server can run simultaneously, 12 encryption methods |
| OpenVPN Encryption |
DES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF-CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC, AES-192-CBC, AES-256-CBC |
| IPSec |
IKEv1, IKEv2, with 5 encryption methods for IPsec (DES, 3DES, AES128, AES192, AES256) |
| GRE |
GRE tunnel |
| PPTP, L2TP |
Client/Server instances can run simultaneously, L2TPv3 support (planned) |
| Stunnel (planned) |
Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code |
| DMVPN (planned) |
Method of building scalable IPsec VPNs |
| SSTP (planned) |
SSTP client instance support |
| ZeroTier |
ZeroTier VPN client support |
| WireGuard |
WireGuard VPN client and server support |
| MODBUS |
Modbus TCP Slave (PLANNED) |
| ID filtering |
Respond to one ID in range [1;255] or any |
| Allow remote access |
Allow access through WAN |
| Custom registers |
Modbus TCP custom register block, which allows to read/write to a file inside the router, and can be used to extend Modbus TCP slave functionality |
Modbus TCP Master (PLANNED) |
| Supported functions |
01, 02, 03, 04, 05, 06, 15, 16 |
| Supported data formats |
8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII |
MQTT Gateway (PLANNED) [/iconheading] |
| Gateway |
Allows sending commands and receiving data from Modbus Master trough MQTT broker |
Data to Server (PLANNED) [/iconheading] |
| Protocols |
HTTP(S), MQTT, Azure MQTT, Kinesis |
Monitoring & Management |
| WEB UI |
HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log |
| FOTA |
Firmware update from server, automatic notification |
| SSH |
SSH (v1, v2) |
| SMS |
SMS status, SMS configuration, send/read SMS via HTTP POST/GET |
| Call |
Reboot, Status, Mobile data on/off, Output on/off |
| MQTT (planned) |
MQTT Broker, MQTT publisher |
| SNMP (planned) |
SNMP (v1, v2, v3), SNMP trap |
| JSON-RPC |
Management API over HTTP/HTTPS |
| Modbus (planned) |
Modbus TCP status/control |
| RMS |
Teltonika Remote Management System (RMS) |
IoT Platforms |
| Clouds of things |
Allows monitoring of: Device data, Mobile data, Network info, Availability |
| ThingWorx |
Allows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network Type |
| Cumulocity |
Allows monitoring of: Device Model, Revision and Serial Number, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength, WAN Type and IP |
| Azure IoT Hub |
Can send device IP, Number of bytes send/received, Mobile connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, SIM State, PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type, Temperature, PIN count to Azure IoT Hub server |
System Characteristics |
| CPU |
QCA9531, MIPS 24kc, 650 MHz |
| RAM |
128 MB, DDR2 |
| FLASH storage |
16 MB, SPI Flash (optional up to 256 MB) |
Firmware / Configuration |
| WEB UI |
Update FW from file, check FW on server, configuration profiles, configuration backup |
| FOTA |
Update FW/configuration from server |
| RMS |
Update FW/configuration for multiple devices at once |
| Keep settings |
Update FW without losing current configuration |
Input/Output |
| Configurable I/O |
2 x Configurable digital Inputs/Outputs. Digital input 0 – 6 V detected as logic low, 8 – 30 V detected as logic high. Open collector output, max output 30 V, 300 mA |
| Events |
SMS, Email, RMS |
Power |
| Connector |
4 pin industrial DC power socket |
| Input voltage range |
9 – 30 VDC, reverse polarity protection, voltage surge/transient protection |
| Power consumption |
10.5 W max |
Physical Interfaces (Ports, Leds, Antennas, Buttons, SIM) |
| Ethernet |
2 x RJ45 ports, 10/100 Mbps |
| I/Os |
2 x Configurable digital Inputs/Outputs on 4 pin power connector |
| Status LEDs |
2 x Mobile connection type, 3 x Mobile connection strength, 2 x Eth status, 1 x Power |
| SIM |
1 x SIM slots (Mini SIM – 2FF), 1.8 V/3 V, external SIM holders |
| Antenna |
2 x SMA for LTE, 2 x RP-SMA for WiFi |
| Power |
1 x 4 pin DC connector |
| Reset |
Reboot/User default reset/Factory reset button |
Physical Specification |
| Casing material |
Aluminium housing with DIN rail mounting option |
| Dimensions (W x H x D) |
100 x 30 x 85 mm |
| Weight |
247 g |
| Mounting options |
DIN rail, flat surface placement |
Operating Environment |
| Operating temperature |
-40 C to 75 C |
| Operating humidity |
10 % to 90 % non-condensing |
